WP-TSURUMI 50PUA2.4S AUTO

An air pump for aquariums is an advantage during the night since plants need light to produce oxygen. In thinly planted aquariums the air pump supplies the necessary water circulation. In aquariums with dense planting the air pump provides the aquarium with oxygen at night, since the number of plants means the oxygen concentration can drop to a dangerous level. When disease is present in the aquarium the air pump increases the oxygen level in the water, an essential condition for many medications. Simple to connect Connect hose with air pump. Cut air hose and insert check valve. Cut the remaining hose to the desired length. Connect one end with check valve and other end with air stone. If possible mount the pump on the wall next to the aquarium. Hook for hanging up attached.

• For a reliable oxygen supply in aquariums: ready-to-install diaphragm pump with check valve and air stone - 50 l/h air outlet, > 160 mbar head pressure, 2.3 W power consumption
• Easy to install: connect pump with air hose and air stone, mount pump outside aquarium, place air stone in the aquarium
• Noise suppression air chamber, reinforced housing wall, vibration dampening rubber feet
• With a device for hanging, GS tested, 2.3 W and 50 l/h air output, > 160 mbar air pressure
• Package contents: air pump for aquariums from 10 - 50 l, 2 m air hose, air stone and check valve to prevent water backflow

 

The Resun Air Pump LP100 delivers with low noise a maximum high volume air output of 8400L/hr (140 litres per minute), which is suitable for larger aerobic biocycle sewage systems & fish and koi ponds. It must be housed to be protected from dust ingestion. Dust will prematurely wear the rubber valves & diaphragms. Installation hints:

• Do not install any brand of air pump of this size in the lounge room unless you like a continuous low noise hum whilst watching TV. Place the pump in a non-habitable room, or outside, and then plumb air line tubing to the tank diffusers.
• To increase the life of the rubber diaphragms, the unit must have back pressure. See details below.

Also used for: Air lift water pumping & aeration, Waste water treatment aeration, biocycle, envirocycle & ecocycle deep water septic tank aeration, Natural swimming pond aeration, Aquaculture pond aeration, Commercial and industrial water aeration, Bubble baths FEATURES

• Electromagmetic linear diaphragm technology
• Low noise. Decibel levels measured in a quiet room using A-frequency weighting with medium back pressure loading on the pump: 44dB(A)+/- at 3m from air pump, 55dB(A)+/- at 500mm from air pump. A quite room ambient noise level is 30dB(A)+/-
• Cast aluminium body
• Voltage/Wattage: 240V / 100W
• Automatic thermal cut-out overload protection
• Cable length: 1.5m
• Max pressure: 0.042 mPa / 0.42 bar / 420 mbar / 6.1 psi
• Max air output: 8400L/hr (140 Litres/minute)
• Air pump outlet diameter: 20mm
• Must be set-up above the water level
• Important: Rated IPX4 (meaning - Should be placed in a low dust environment but will tolerate rain and light sprinkling)
• Maximum water depth for placed airstones or air diffuser: 4.0m
• Supplied with a plastic 33 outlet x 46mm barbed manifold to suit 4mm - 8mm silicon air line
• Air Pump dimensions: 270mm(L)x200mm(W)x230mm(H)
• Weight: Air Pump, 6.6kg. Cartoned pump: 7.31kg

PLEASE NOTE: To avoid premature or unexpected failure of the rubber diaphragms and valves:

• As preventive maintenance, the industry standard would require that all linear electromagnetic air pumps running 24/7 should be dismantled, air jet cleaned & have the diaphragms & valves replaced every 18 months or 12,000 hours
• The pump must only be used in a dust free environment.
• The pump must only be run with a back pressure load. Do not use for long periods with unrestricted air flow. This will stretch the diaphragms to cause premature tearing or distortion. Back pressure is created by having the air diffusers or air stones deep in the water or if not possible, a flow control tap fitted into the air line.